replace pull cord on mower

Replace pull cord on mower

Eventually, you're lawnmower pull cord will break. Fortunately it's an easy fix. Check out this video on how to fix

This DIY lawn mower repair guide has instructions for how to replace a lawn mower starter rope. Over time, the starter rope can wear out and eventually break, and the mower won't start. You can replace a broken recoil starter rope with a manufacturer-approved replacement part by following the steps below. Remove the dipstick tube from the engine and plug the hole with a paper towel to keep debris from falling into the engine. Remove the bolts securing the blower housing to the engine and remove the housing from the engine.

Replace pull cord on mower

By: Author John Cunningham. Replacing a pull cord can be challenging, especially if the recoil spring gets loose. Taming a recoil spring can be like herding cats. Replacing the cord requires the removal of the pull start assembly. Some manufacturers, like Honda, make it easy. Other mowers may take a little more work. If your spring is damaged or unravels, go ahead and buy a whole spring and pulley. This post covers pull cord replacement pretty well. Your mower may look different from the models used in the demo shots here, but no matter the repair procedure will be very similar to most mowers. Pull the cord out all the way, secure the pulley, use a screwdriver to lock the spokes of the pulley, and stop it from retracting. Fit the pull handle and double knot. Remove your screwdriver and test. The cord-replacement process is just slightly longer. Remember, when the cord breaks, the pull assembly spring unloads, and so the spring must be wound up to reload it. In the guide below, I have removed the starter pulley from the assembly to fit the cord.

Then came a different kind of break. Honda uses a left-hand thread here, meaning to remove turn clockwise. He was also a consumer electronics repair tech and shop owner for a little over 20 years, until his impending obsolescence became impossible to ignore.

The pull cord is used to start the lawn mower; it can often become broken or need replacement. Additionally, make sure you have a large table for the replacement and a rag nearby for wiping off any grease and oil. Make sure the the engine is off and the spark plug wire is removed and away from the spark plug before begining. Use a Phillips 2 screwdriver to remove the two 25mm screws on top of the engine cover. Use your hands to lift the engine cover off, separating it from the rest of the engine. Remove the oil funnel from the rest of the engine. It should pull away easily and come off completely.

At some point, all household maintenance tools are subject to wear and tear, and your lawn mower is no exception. A broken lawn mower pull cord is a pretty common problem. And fortunately, it is easy to get done DIY. When a pull cord is broken, it means that the starter rope has detached from the rest of the cord. The starter rope is the visible part of the cord. You can access it from outside of the mower. Make sure you replace it if it breaks.

Replace pull cord on mower

Now you could let the pull cord snap just before you want to start mowing, but this makes for a long day. Pull cords on lawn mowers are usually made of a pretty strong nylon rope. While nylon rope is a sturdy material, the friction between the rope and the starter housing will eventually wear it down. So, no matter how careful you are with your pull starter, the time will come when your cord will wear down and need replacing. After all, the cord is designed to be a certain length to turn over the engine and get the fuel pump pumping and the coil sparking the spark plug. You should be able to find this information in your user manual.

That1iggirl

Remove the screws that secure the fuel tank to the engine. Step 5. John Cunningham is an Automotive Technician and writer at Lawnmowerfixed. This is a simple one, but it is worth checking. Old dried grass and debris can collect under the mower; this can prevent the blade from turning and, consequently, the pull cord. Feed the starter rope handle through the engine cover up to the rope guide. Some repairs should only be performed by a qualified technician. This seals the fibers and makes it much easier to thread the cord. About Steve More from author. Add additional length as needed if the cord broke farther from the handle.

The first thing to do is head to your local home improvement store and get a replacement starter cord. Depending on your mower you may need to buy the entire starter cord assembly with the rope already installed.

Feed — While holding the loaded starter pulley, locate the cord end that you marked earlier. Reconnect the spark plug wire. Here are a couple of other common pull cord symptoms I hear a lot:. Repair difficulty. This provides slack to make a new knot where you made your mark earlier. Slide the rope through the hole in the engine cover. Depending on your starter handle, you may need to drive the knot out with a slotted screwdriver and mallet so you can grab hold of it to remove the cord. You're Finished! Why won't my lawn mower move? Now back the pulley off a full rotation, plus enough extra to align the tie-off hole in the pulley with the cord guide hole in the housing. Too much oil is also bad for the engine. Video Library. Needle — The needle and float together to control gas flow to the fuel bowl.

1 thoughts on “Replace pull cord on mower

Leave a Reply

Your email address will not be published. Required fields are marked *