plotter graphtec ce5000

Plotter graphtec ce5000

I got a new HP computer with windows I can't get it plotter graphtec ce5000 recognize my graphtec ce When i plug in the. Hopefully after you downloaded the driver you extracted and ran it.

I've been scouring the internet for a few days now and haven't really found a good answer to my question. I went to order a zencut green the other day because they appeared to get one back in stock but I was out of luck, so now I have some credit towards another cutter and I'm thinking about making the jump to a graphtec. The driving force behind my decision on the zencut was the price and the servo motor. The graphtec isn't as nice of a price but I'm still interested in getting a machine that does a better job than my current MH series. I talked to someone who claimed the CE was mostly superficial updates over the CE and that I would be better off saving some money and getting the CE starter kit less money, plus a bunch of supplies. So my questions:.

Plotter graphtec ce5000

When the new Graphtec CE cutter was delivered, an engineer came round and got me started with a brief introduction. I was shown how the different settings apply and received some basic tips including a good explanation about the importance of the offset setting. An incorrect offset setting means less accurate corners and more difficult weeding. I haven't had to re-adjust the offset yet as the variety of vinyl I've used to date has been limited; but at least I was made aware of it, so when I do use a different degree blade or thicker vinyl, I'll know what to do. While the engineer was there we did a few test cuts with the offset at different settings so that I could recognise when it is set incorrectly. Because the centre of the blade is not where the cut is usually made, the machine has to send the centre of the blade past the point to be cut, by an amount that relates to the offset see diagram left ; otherwise the blade will cut past or not up to the point it is supposed to and therefore the cut lines either don't meet or they overlap, and weeding the vinyl becomes difficult. The two images below show the corners becoming rounded off when an incorrect offset has been used to cut a 1cm square of vinyl. The vinyl should have been cut to a perfect square with the triangle inside it as the third image shows. I had two problems only when using the Graphtec CE and neither of these were to do with the machine itself. The first was to do with accurate cutting over long lengths. The tracking of this machine is so good that whenever there was a problem, it was always down to me. Either I was using vinyl wound too loosely on the roll or I hadn't lined up the roll correctly on the machine, although this should have been simple with the guidelines that the CE has. One weekend when I was happily cutting away on a job to be completed by that Monday, the Cutting Master 2 plugin just stopped working suddenly, for no apparent reason.

I started with greenstar because it was cheaper but as I need to buy more stock I typically 'upgrade' to oracle in that color.

.

Table Of Contents. Table of Contents. Quick Links. CE Series. Previous Page. Next Page. Page 7 5. If any item is missing, please contact your sales representative or nearest Graphtec vendor promptly.

Plotter graphtec ce5000

When the new Graphtec CE cutter was delivered, an engineer came round and got me started with a brief introduction. I was shown how the different settings apply and received some basic tips including a good explanation about the importance of the offset setting. An incorrect offset setting means less accurate corners and more difficult weeding. I haven't had to re-adjust the offset yet as the variety of vinyl I've used to date has been limited; but at least I was made aware of it, so when I do use a different degree blade or thicker vinyl, I'll know what to do. While the engineer was there we did a few test cuts with the offset at different settings so that I could recognise when it is set incorrectly.

Mini market near me open now

Sign in here. I made the leap to a new cutter this year and it's great. I don't mind spending the extra money and getting the newer model, I just want to have peace of mind that I'm not just buying a newer name plate on the case. So which cutting software are you using? From what I can tell the cuts a bit faster, but I rarely cut at full speed anyway and my orders are not so large and so frequent that I need to minimize the time the material is on the cutter. Share this post Link to post Share on other sites. I recently started doing sand blast and my Summa only goes to g and it is JUST enough to get through the cheap sandblast resist that USCutter sells. Did you set the correct Command on the vinyl cutter, for the cutting software? Regardless that's not really my question, even if only on the basis of having scrap rolls around to do practice cuts on there is still an inherent value in the extra supplies that come with the CE starter bundle. The first was to do with accurate cutting over long lengths. I've been scouring the internet for a few days now and haven't really found a good answer to my question.

.

I did just notice that the CE bundle comes with an extra year of warranty over the CE, which could be useful. Additionally I will not be getting rid of my MH series cutter so if the need for a wider graphic did arise I would still have it available. I went to order a zencut green the other day because they appeared to get one back in stock but I was out of luck, so now I have some credit towards another cutter and I'm thinking about making the jump to a graphtec. Like I said, the zencut green was discounted because IT was being discontinued, not the Puma. The only differences I've come across are an increased cutting pressure and speed for the CE The driving force behind my decision on the zencut was the price and the servo motor. From what I can tell the cuts a bit faster, but I rarely cut at full speed anyway and my orders are not so large and so frequent that I need to minimize the time the material is on the cutter. They'd been advised to just upgrade the Cutting Master 2 plugin, which is exactly what I did. I'm also expecting them to have a biased opinion just like the vendors, which was why I wanted first hand experiences from people without an agenda. I have a 30" cutter collecting dust right now. I don't mind spending the extra money and getting the newer model, I just want to have peace of mind that I'm not just buying a newer name plate on the case. Sign In Sign Up. I quickly discovered someone who had experienced the same problem and found out that it was probably because I had installed one of the CorelDraw service packs. One option would be to buy the larger CE, which would mean that you are able to cut larger letters and graphics for vehicle wrapping or shop window decoration, which the average local sign maker may not be able to do. I've been scouring the internet for a few days now and haven't really found a good answer to my question.

0 thoughts on “Plotter graphtec ce5000

Leave a Reply

Your email address will not be published. Required fields are marked *