Playstation 2 laser replacement

Disconnect all cables from the console and flip the unit over to reveal its base. Locate the 6 feet on the base of the unit.

Replace the laser assembly in your optical disc drive. Replacing the laser requires you to have or purchase a new laser. Flip the PlayStation 2 over so it lays with the bottom of the device facing upwards. Some models have a different number of screws and feet. Remove all the feet and screws in the bottom of the case. The 10 screw model has 6 screws in the bottom-most portion and 4 in the upper tray. Peel the warranty sticker located next to the main power switch straight away from the case.

Playstation 2 laser replacement

Use this guide to help identify which optical laser lens replacement will fit your PlayStation 2 console. Note: Replacing the laser lens will normally require a soldering iron to remove an anti static point solder blog before install. Laser lens models can normally be identified from the console model but it is always advisable to physically remove and check the old laser prior to ordering any replacement to ensure that it is the model you expected, and that the new part is the same model or listed as a compatible replacement for the model of laser you have. Lasers will need to be fitted to the deck unit inside the console, this requires some additional rebuilding, unscrewing runners to remove the old laser and put the new one in place. This is only a few additional steps but if you are less confident with completing the repair, or you believe other parts of the laser mechanism is not working properly, you can opt to purchase the deck with the laser pre-installed. Remember the anti static solder blob will still need to be removed prior to installation or the laser will not operate, this applies to all laser units, whether attached to the deck or not. This site uses cookies to provide you with a great user experience, by using ZedLabz. Discover the latest stuff from our wide range of partners, including exclusives only available at ZedLabz. Gaming display stands See More "Close Cart". Merchandise See More "Close Cart".

If you replace the laser, it won't matter, you can even practice how to open it and close it. Use your fingernail to flip up the retaining flap on the optical disc drive laser ribbon cable. Step 3.

.

Disconnect all cables from the console and flip the unit over to reveal its base. Locate the 6 feet on the base of the unit. Pry them off using a spudger to reveal the screws. Note: One of the feet is located under the sticker shown in the photo. Removing this sticker will void any warranty with Sony. Remove all six 4. Starting at the corner at which the power and Ethernet ports are located, pry open the outer shell using a spudger and continue around the entire unit. Note: You may use your hands for additional force to separate the two pieces of the outer shell. Take the silver rail with your tweezers and pull it towards yourself to take it out. Be carefull, as it still attached to the laser, just guide it slowly towards yourself.

Playstation 2 laser replacement

The screws on the right are a bit deeper inside the shell as like the rest but are the same size. Separate the clips at the front and the overhanging side from their mounting using a Prying Tool. With a plastic tool, lightly press down these two levers at the same time. Ideally, the CD should now start to spin. If it doesn't spin, the whole drive or other parts of it may be damaged and need to be replaced. Now, there are 3 flat cables to disconnect. Caution: Some have a small clamp that must first be released, so that you can carefully pull them out.

Aritra dutta banik wife

You're Finished! Step 6 Remove silver rail. Carlos Bragatto - Feb 16, Badges: Small - px Medium - px Large - px. Leave a comment Name Email. Almost done! Step 10 Place the new laser in. Some ps2 consoles have only 1 hex adjustment yet others have 2. Use this guide to help identify which optical laser lens replacement will fit your PlayStation 2 console. Hi Mark! Step 8 Desoldering the anti-static security. Badges: Gaming display stands See More "Close Cart".

Use this guide to help identify which optical laser lens replacement will fit your PlayStation 2 console. Note: Replacing the laser lens will normally require a soldering iron to remove an anti static point solder blog before install.

The 10 screw model has 6 screws in the bottom-most portion and 4 in the upper tray. Alexander Wiand - Nov 8, Reply. What you need. Some ps2 consoles have only 1 hex adjustment yet others have 2. Step 5 Remove screws and brackets. Note: One of the feet is located under the sticker shown in the photo. Fix Your Stuff Community Store. Be carefull, as it still attached to the laser, just guide it slowly towards yourself. Load more comments. Author with 7 other contributors. To reassemble your device, follow these instructions in reverse order.