Lawn mower starter cord replacement

This DIY lawn mower repair guide has instructions for how to replace a lawn mower starter rope.

With perfect weather, you plan to go out to give your lawn a nice trim. You use a push mower that has never let you down in all these years. The other end is spinning back into the starter assembly. You are not the only one with this problem. It occurs more frequently with older lawnmowers, and in most cases, you have to replace the pull cord.

Lawn mower starter cord replacement

Own a lawnmower long enough, and eventually, you will experience small engine pull cord failure. Whether your lawnmower pull cord has seen its fair share of uses or it fails before its time due to quality, these seven simple steps will show you exactly how to replace pull cord on mowers to get you back up and running before your next mowing mission. SGT KNOTS Dacron Polyester Pull Cord is the heavy-duty, ultra-reliable replacement pull cord and starter rope every landscaping business, homeowner, or neighborhood lawn care kid should have hanging in their garage for on-the-fly fixes. This cord is as cost-effective as it is reliable with a Dacron polyester solid-braid construction resistant against abrasion and wear. Snag this cord in either 4, 5, or 6 diameters and lengths of 10ft and 25ft, or spools of 50ft, ft, and 1,ft for a never-ending supply of replacement pull cord perfect for everything from mowers, generators, leaf and snow blowers, and more. Now that you know how to replace a mower pull cord, you can move onto your next DIY repair or improvement project. Thankfully, you can count on SGT KNOTS to provide you with the best Rope and Cord products and all the information you need to get back up and running no matter what type of mission is next on your list. November 3, Mike Shelley. Leave a comment Comments must be approved before appearing. Added to your cart:. Cart subtotal.

Connect the plastic cover of the engine: 2 Related Questions: 2.

Now you could let the pull cord snap just before you want to start mowing, but this makes for a long day. Pull cords on lawn mowers are usually made of a pretty strong nylon rope. While nylon rope is a sturdy material, the friction between the rope and the starter housing will eventually wear it down. So, no matter how careful you are with your pull starter, the time will come when your cord will wear down and need replacing. After all, the cord is designed to be a certain length to turn over the engine and get the fuel pump pumping and the coil sparking the spark plug. You should be able to find this information in your user manual. Before I tackle any repair with my lawn mower, I always pop off the spark plug to avoid any unexpected accidents.

Written by: Steve. October 3, As an Amazon Associate we earn from qualifying purchases more. If you own a pull start lawn mower you will eventually find yourself holding the severed handle of a broken starter cord. Here in Florida, two thirds of the year is one continuous lawn mowing session.

Lawn mower starter cord replacement

The pull cord is used to start the lawn mower; it can often become broken or need replacement. Additionally, make sure you have a large table for the replacement and a rag nearby for wiping off any grease and oil. Make sure the the engine is off and the spark plug wire is removed and away from the spark plug before begining. Use a Phillips 2 screwdriver to remove the two 25mm screws on top of the engine cover.

Blenders at walmart

Set cap aside. Learn how to re…. November 1, at pm. Old grass or debris caught inside the pulley: 2. Why does my lawn mower stall? September 17, at pm. May 4, at am. Remove the plastic cap: 1. Thank you for your feedback, Hannah. Replace it as needed to avoid any issues.

Are you struggling with a broken pull cord on your lawnmower? With our step-by-step instructions, your Briggs and Stratton lawnmower will be up and running quickly. How to replace the pull cord on a Briggs and Stratton lawnmower:.

The cord-replacement process is just slightly longer. When you pull the cord, the pull cord rotates, and the piston moves. The key usually shears because the blade has hit something solid, and the engine has come to a sudden stop. Rotate the pulley in a counter-clockwise direction: 1. Ok, we are almost done. We know that after this hectic job, you might be a little tired. The above article is a step-by-step guide for fixing the pull cord. The starter housing on my starter assembly has a small recess that the knot sits in. Use the advice and tips in these articles and videos to get the most out of your walk-behind lawn mower. June 7, at am. How long is the lawnmower cord supposed to be?