Ipod nano button stuck

To start the conversation again, simply ask a new question. Page content loaded.

A system is only as strong as its weakest link and [Roberto Barrios] found that on the sixth generation iPod nano the buttons are the problem. Each consist of a couple of parts; the tactile piece that you see and press, the electrical switch which converts that force into an electrical signal, and a shim that bridges the gap between the two. After two months of use the iPod [Roberto] was fixing had stopped responding to presses of the Power button. It turns out that the shims are attached with double-sided tape. Inspection of the internals revealed that the shim had slid to one side and no longer made contact with the electrical system. With the shim back in place all is well but he made sure to execute this fix on all of the buttons before reassembly.

Ipod nano button stuck

Repair information for the 6th generation iPod nano. Released in September of Model Number: A Emily Routh emilyrouth. Posted: Jan 29, The power button on my iPod Nano 6th Generation is stuck. As in, my iPod won't turn on unless I plug it into the computer to make it light up. Please help! I took mine back to the apple store and met with a genius. They replaced the nano under warranty.

Ask a question Reset.

I will document what I did to fix it here. This article may also be useful for those looking to dismantle or fix their iPod Nano 6th Gen since most of the steps contained here will allow you to access all components of the device. By performing this fix, there is also the chance that you may damage your iPod, so beware of this before you attempt to DIY. I cannot be responsible if you make a mistake! You may be looking at the iPod and wondering how on Earth is it possible to open something with no visible screws? You will need tools. Preferably you would buy some plastic opening tools from eBay since they are less likely to damage the device.

Use this article for help with your iPod classic, iPod nano, and iPod shuffle. Need help with an iPod touch instead? If your iPod doesn't respond, use the following instructions to force restart it. Find out which model of iPod you have. Turn off your iPod with its power switch. If you see green by the switch, your iPod is on. Move the Hold switch firmly to the off position so that you don't see orange by the switch. Press and hold the Menu button and Center or Select button for 8 seconds, or until you see the Apple logo.

Ipod nano button stuck

If your iPod isn't responding, a simple force restart should unfreeze it. You only need to know which buttons to press and in what order to force the device to reboot and reload its software. A force restart is a hardware-level reset that physically cuts off power flow from the battery to the logic board. This causes your music player to turn off and restart without deleting your settings, music, or data. Apple no longer sells the iPod, but that's hardly stopping enthusiasts from dusting off their rusty old music players. Yes, you can still use the original iPod today , although you might encounter random freezes, sudden restarts, and unresponsiveness. If your iPod is acting up, the first troubleshooting step is confirming that the Hold switch is in the OFF unlocked position.

Pick 3 for ohio

Mount your IPod again, without remounting the rightmost screw. Inspection of the internals revealed that the shim had slid to one side and no longer made contact with the electrical system. How shall it work with the headphones? It should pop right up. I used a online repair shop named iRefresh. Posted: Feb 3, Please please please do not try to repair yourself until youve taken the ipod back to the Apple store. The problem is that the button can't be pushed in far enough to make contact with the loosely taped internal button. I have a friend who routinely does iPod and iPhone repair as a business and he can do this quickly and relatively affordable. Posted: Aug 7, Options Permalink History. I unscrewed the metal plate behind the display. Just take some Peroxicide on a q-tip very lighty and dab it around the edges of the button.

To start the conversation again, simply ask a new question.

Ask a question Reset. Once the back edge is clear, gently pull it towards the left and upwards over the ribbon cable. They sell the part and install it if you want. You can always add one more layer if it ends up not being thick enough. I took it back to the Apple store and they said it would cost Fix Your Stuff Community Store. Thank you so much for this tutorial! Note how it clips into the bottom right and left top of the iPod shell. Thanks a lot! Posted: Oct 9, Options Permalink History. Please be kind and respectful to help make the comments section excellent.