Fanuc 21i-t parameter manual

Upload aoaby. Embed Size px x x x x Warning notices are used in this publication to emphasize that hazardous voltages, currents,temperatures, or other conditions fanuc 21i-t parameter manual could cause personal injury exist in this equipment ormay be associated with its use.

Follow along with the video below to see how to install our site as a web app on your home screen. Note: This feature may not be available in some browsers. This website or its third-party tools process personal data e. To learn more, please refer to the cookie policy. In case of sale of your personal information, you may opt out by sending us an email via our Contact Us page. To find out more about the categories of personal information collected and the purposes for which such information will be used, please refer to our privacy policy.

Fanuc 21i-t parameter manual

Warning Warning notices are used in this publication to emphasize that hazardous voltages, currents, temperatures, or other conditions that could cause personal injury exist in this equipment or may be associated with its use. In situations where inattention could cause either personal injury or damage to equipment, a Warning notice is used. Caution Caution notices are used where equipment might be damaged if care is not taken. Note Notes merely call attention to information that is especially significant to understanding and operating the equipment. This document is based on information available at the time of its publication. While efforts have been made to be accurate, the information contained herein does not purport to cover all details or variations in hardware or software, nor to provide for every possible contingency in connection with installation, operation, or maintenance. Features may be described herein which are not present in all hardware and software systems. GE Fanuc Automation assumes no obligation of notice to holders of this document with respect to changes subsequently made. GE Fanuc Automation makes no representation or warranty, expressed, implied, or statutory with respect to, and assumes no responsibility for the accuracy, completeness, sufficiency, or usefulness of the information contained herein. No warranties of merchantability or fitness for purpose shall apply. All Rights Reserved. For details, refer to the Specifications BEN.

This specification reduces the number of buffering interruptions caused by reading of a series of blocks specifying short movements. Parameter sets the maximum speed for the second spindle. Chapter 07 Chapter

.

Warning notices are used in this publication to emphasize that hazardous voltages, currents, temperatures, or other conditions that could cause personal injury exist in this equipment or may be associated with its use. In situations where inattention could cause either personal injury or damage to equipment, a Warning notice is used. Notes merely call attention to information that is especially significant to understanding and operating the equipment. This document is based on information available at the time of its publication. While efforts have been made to be accurate, the information contained herein does not purport to cover all details or variations in hardware or software, nor to provide for every possible contingency in connection with installation, operation, or maintenance. Features may be described herein which are not present in all hardware and software systems. GE Fanuc Automation assumes no obligation of notice to holders of this document with respect to changes subsequently made. GE Fanuc Automation makes no representation or warranty, expressed, implied, or statutory with respect to, and assumes no responsibility for the accuracy, completeness, sufficiency, or usefulness of the information contained herein.

Fanuc 21i-t parameter manual

Warning notices are used in this publication to emphasize that hazardous voltages, currents, temperatures, or other conditions that could cause personal injury exist in this equipment or may be associated with its use. In situations where inattention could cause either personal injury or damage to equipment, a Warning notice is used. Notes merely call attention to information that is especially significant to understanding and operating the equipment. This document is based on information available at the time of its publication. While efforts have been made to be accurate, the information contained herein does not purport to cover all details or variations in hardware or software, nor to provide for every possible contingency in connection with installation, operation, or maintenance. Features may be described herein which are not present in all hardware and software systems. GE Fanuc Automation assumes no obligation of notice to holders of this document with respect to changes subsequently made. GE Fanuc Automation makes no representation or warranty, expressed, implied, or statutory with respect to, and assumes no responsibility for the accuracy, completeness, sufficiency, or usefulness of the information contained herein. No warranties of merchantability or fitness for purpose shall apply. ParametersCommon to all Channels.

Multi device mouse

When LGT is 1, it is always canceled. Prices Prices. Set the maximum number of times the system retries holding communication with the remote device if the remote device uses an invalid protocol in the datalink layer or the remote device does not respond to the request. Example When 30 is set, 32 ms is assumed. Up to the maximum value counted by the reference counter can be specified as the grid shift. SK0 This parameter specifies whether the skip signal is made valid under thestate of the skip signal SKIP bit 7 of X and the multistage skipsignals bits 0 to 7 of X for the T series only. Diameter of a tailstock D1 Uploaded by Lam Pham. This parameter determines the maximum length of the packet used in transmission over the DNC2 interface. Only when the LGT parameter bit 4 of No. When 0 is set in this parameter, nosynchronization error check is made. The data is displayed in re-verse video. Regardless of whether input is made in mm or inches, the machine position is displayed in mm for millimeter machines, or in inches for inch machines. However, parameter No. Set the number of the pitch error compensation position at the extremelynegative position for each axis.

.

Forthe valid data range of a specific parameter, see theexplanation of the parameter. Set parameter No. M02 When M02 is specified in memory operation 0 : M02 is sent to the machine, and the head of the program is automatically searched for. A corresponding position switch signal is output to PMC when the machine coordinate value of a corresponding axis is within the range that is set using a parameter. When GST, 1 of parameter , is set to 1, set the spindle motor speedduring spindle gear shift calculated from the following formula. Usually set the value of T2 to 24 ms ir 32 ms. This parameter sets the lower limit of the percentage of the cuttingfeedrate changed repeatedly in a peck drilling cycle of a small diameter tothe specified cutting feedrate. This parameter sets the time from the detection of an abnormal load until aservo alarm is issued. Up to five axes can be selected. Set parameter No. NOTEA sequence number can also be set by using the settingscreen. So this parameter must be set; it will not be set automatically.